1 copyright ? 2010, everli ght americas inc . all rights reserved. release date : 5/2 8/ 201 3 . issue no: 1 rev : 1 www.everlightamericas.com 1206 package infrared chip led with inner lens EAIST3015A1 features ? small double - end package ? high reliability ? low forward voltage ? good spectr al matching to si photodetector ? package in 8mm tape on 7 diameter reel ? pb free ? the product itself will remain within rohs compliant version. descriptions EAIST3015A1 is an infrared emitting diode in miniature smd package which is molded in a water cle ar plastic with flat top view lens. the device is spectrally matched with silicon photodiode and phototransistor. applications ? pcb mounted infrared sensor ? infrared emitting for miniature light barrier ? floppy disk drive ? optoelectronic switch ? smoke de tector device selection guide part no. chip material resin color EAIST3015A1 gaalas water clear
data sheet 1206 p ackage infrared chip led with inner lens EAIST3015A1 2 copyright ? 2010, everlight americas inc . all rights reserved. release date : 5/2 8/ 201 3 . issue no: 1 rev : 1 www.everlightamericas.com package dimensions notes: 1.all dimensions are in millimeters 2.tolerances unless dimensions 0.1mm
data sheet 1206 p ackage infrared chip led with inner lens EAIST3015A1 3 copyright ? 2010, everlight americas inc . all rights reserved. release date : 5/2 8/ 201 3 . issue no: 1 rev : 1 www.everlightamericas.com absolute maximum ratings (ta=25 parameter symbol rating units reverse voltage v r 5 v continuous forward current i f 65 ma power dissipation at(or below) 25 free air temperature p d 130 mw operating temperature t opr - 25 ~ +85 storage temperature t stg - 40 ~ + 100 soldering temper ature tsol reflow soldering : 260 for 10 sec. hand soldering : 350 for 3 sec. electro - optical characteristics (ta=25 symbol min. typ. max. unit condition radiant intensity ie 1.25 2.25 ---- mw/sr i f = 20 ma viewing angle 2 1/2 ---- 100 --- - deg peak wavelength p ---- 940 ---- nm spectrum radiation bandwidth ---- 45 ---- nm forward voltage v f ---- 1.2 1.5 v reverse current i r ---- ---- 10 a v r =5 v
data sheet 1206 p ackage infrared chip led with inner lens EAIST3015A1 4 copyright ? 2010, everlight americas inc . all rights reserved. release date : 5/2 8/ 201 3 . issue no: 1 rev : 1 www.everlightamericas.com typical electro - optical characteristics curves fig.1 forward curren t vs. fig.2 spectral distributio n ambient temperature f ig.3 peak emission wavelength fig.4 forward current ambient temperature vs. forward voltage 0 -25 0 40 20 60 100 80 20 40 60 100 80 120 140 0 20 40 60 80 100 i f =20ma ta=25 c 75 -25 900 0 920 940 25 50 960 980 100 0 10 10 1 10 2 3 10 4 1 2 3 4
data sheet 1206 p ackage infrared chip led with inner lens EAIST3015A1 5 copyright ? 2010, everlight americas inc . all rights reserved. release date : 5/2 8/ 201 3 . issue no: 1 rev : 1 www.everlightamericas.com typical electro - optical charact eristics curves fig.5 relative intensity vs. fig.6 relative radiant intensity vs. forward current angular displacement -20 0.6 0.9 0.7 0.8 1.0 0.2 0.4 0 0.2 0.4 0.6 50 70 80 60 40 30 -10 0 20 10 0 i f -forward current (ma ) 10 10 0 10 1 10 2 3 10 4 ie-radiant intensity(mw/sr) 1 10 100
data sheet 1206 p ackage infrared chip led with inner lens EAIST3015A1 6 copyright ? 2010, everlight americas inc . all rights reserved. release date : 5/2 8/ 201 3 . issue no: 1 rev : 1 www.everlightamericas.com precautions for use 1. over - current - proof customer must a pply resistors for protection, otherwise slight voltage shift will cause big current change (burn out will happen ). 2. storage 2.1 do not open moisture proof bag before the products are ready to use. 2.2 before opening the package: the leds should be kept at 30 or less and 90%rh or less. 2.3 the leds should be used within a year. 2.4 after opening the package, the leds should be kept at 30 or less and 6 0%rh or less. 2.5 the leds should be used within 168 hours (7 days) after opening the package. 2. 6 if the moisture absorbent material (silica gel) has faded away or the leds have exceeded the storage time, baking treatment should be performed using the following conditions. baking treatment : 605 for 48 hours. 3. soldering condition 3.1 pb - free solder tempe rature profile 3.2 reflow soldering should not be done more than two times. 3.3 when soldering, do not put stress on the leds during heating. 3.4 after soldering, do not warp the circuit board.
data sheet 1206 p ackage infrared chip led with inner lens EAIST3015A1 7 copyright ? 2010, everlight americas inc . all rights reserved. release date : 5/2 8/ 201 3 . issue no: 1 rev : 1 www.everlightamericas.com 4. soldering iron e ach terminal is to go to the tip of soldering iron temperature less than 350 for 3 seconds within once in less than the soldering iron capacity 25w. leave two seconds and more intervals, and do soldering of each terminal. be careful because the damage of the product is often started at the time of the hand solder. 5. repairing repair should not be done after the leds have been soldered. when repairing is unavoidable, a double - head soldering iron should be used (as below figure). it should be confirme d beforehand whether the characteristics of the leds will or will not be damaged by repairing.
data sheet 1206 p ackage infrared chip led with inner lens EAIST3015A1 8 copyright ? 2010, everlight americas inc . all rights reserved. release date : 5/2 8/ 201 3 . issue no: 1 rev : 1 www.everlightamericas.com package dimensions note: the tolerances unless mentioned are 0.1, unit=mm. carrier t aping dimensions: loaded quantity per reel 2 000pcs/reel note: the tolerances unless mentioned is 0.1mm, unit = mm
data sheet 1206 p ackage infrared chip led with inner lens EAIST3015A1 9 copyright ? 2010, everlight americas inc . all rights reserved. release date : 5/2 8/ 201 3 . issue no: 1 rev : 1 www.everlightamericas.com label form specification cpn: customers production number p/n : production number qty: packing quantity cat: ranks hue: peak waveleng th ref: reference lot no: lot number notes 1. above specification may be changed without notice. everlight americas will reserve authority on material change for above specification. 2. when using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. everlight americas assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 3. these specification sheets include materials protected under copyright of everlight americas corporation. please dont reproduce or cause anyone to reproduce them without everlight americas s consent.
|
